Reels

1. 

   How to wrap a gas cap on a grey car

   Learn how to wrap and trim the gas cap area on a grey car without wrinkling.

   This tutorial shows a grey vinyl wrap being applied to the quarter panel and gas cap of a grey car.

   Wrapping the Gas Cap Recess

   The installer begins on the quarter panel around the fuel door. Messing up the gas cap can ruin the look of the entire wrap. Start by heating the edge and outlining the seam with your finger. For the first cut, cut along the opposite edge on the gas cap side. Give the material a slight pre-tuck before opening the door, then pop it open and complete the tuck on the inside edge.

   Wrapping the Fuel Door

   Next, remove the old piece from the fuel cap door and place down a fresh section of vinyl wrap. Squeegee out all the trapped air from behind the vinyl, apply heat, and lock in the edge. Cut the excess film using the opposite edge on the quarter panel side as a guide. After removing the scrap vinyl, pre-tuck the edges before opening the cap again. A key tip is to work the corners and rounded sections first, which keeps the material from wrinkling on the inside edges.

   Aura Vinyl provides vinyl wrap films featuring a cast polymer hybrid construction and German-made adhesive for easy repositioning and fewer glue lines.

   FAQ

   Where do you cut when wrapping around a fuel door?

   When trimming the quarter panel, cut along the opposite edge on the gas cap side. When wrapping the fuel door itself, use the opposite edge on the quarter panel side as your cutting guide.

   How do you keep vinyl wrap from wrinkling inside the gas cap?

   Pre-tuck the material before popping the door open. Work the corners and rounded areas first to prevent wrinkles from forming on the inside seams.

2. 

   How to Reinstall Emblems on a BMW M3 Wrap

   Learn how to use a tape template to put your car emblems back in their factory position after wrapping.

   This guide demonstrates how to replace badges on a green 1992 to 1999 BMW M3 during a vinyl wrap job. The video shows the step-by-step process of saving the factory emblem positions before wrapping and placing them back on afterward.

   Making the Tape Template

   To keep the badges in their factory position, start by placing masking tape around the entire emblem. Layer extra tape across the area so the template stays together when you pull it off. Using a marker, draw outlines showing exactly where the emblem sits inside the tape. Next, make marks along the edges of the car panel so you can align the template later. Carefully lift the tape template off the car and set it in a safe spot so it does not get damaged or lose its shape.

   Emblem Removal and Reinstallation

   Once the template is stored, remove the badges by cutting behind them with fishing line. Take a rubber wheel on a drill to erase any leftover adhesive foam from the paint surface. After you install your vinyl wrap on the panel, align the tape template back over the panel edges. Apply press-in-place adhesive to the back of the emblems, then set them directly onto the vinyl using your marker guides. After pressing the emblems down, pull away the tape template to complete the reinstallation.

   Aura Vinyl vinyl wrap uses a PET backing and German-made adhesive for a flat finish that supports clean reinstallations.

   FAQ

   How do you save the factory position of car emblems before wrapping?

   Create a tape template around the emblem, double up the tape, and mark the emblem and panel edges with a marker. Store the template safely so it keeps its shape until reinstallation.

   What tool removes leftover emblem adhesive from car paint?

   Use a rubber eraser wheel attached to a drill to clean away leftover adhesive residue after cutting the emblem off with fishing line.

   How do you reattach emblems onto wrapped panels?

   Apply press-in-place adhesive to the emblem backs, position the tape template back on the panel edges, and set the emblems into your marker outlines.

3. 

   How to wrap a door handle in two pieces

   Learn a two-piece door handle wrapping method that locks vinyl edges in place to prevent peeling.

   This tutorial demonstrates a two-piece vinyl wrap technique on a detached door handle to prevent edges from lifting. The video shows an installer wrapping a door handle in stages to ensure the material stays secure and does not fail over time.

   Step-by-Step Handle Wrap Method

   To begin, treat the wrap area as two separate pieces, starting with the outside section. Follow these installation steps:

   • Heat up one side of the vinyl and pull the material over the handle.
   • Work the film into the center of the handle.
   • Cut the material on the inside without going too deep, then trim away any excess.
   • Repeat the heating, pulling, and trimming process on the opposite side.
   • Lay the inside piece over second to lock down the edges from the outside layer.

   Covering the outer edges with the inner piece secures the vinyl seams so they do not peel apart with regular use.

   Film Features

   Aura Vinyl vinyl wrap features a cast polymer hybrid build with German-made adhesive and a PET backing. This design provides pliability and repositioning control during tight corner work on small components.

   FAQ

   Why wrap a car door handle in two pieces?

   Wrapping in two pieces allows you to lay the inner piece over the outside layer. This locks the cut edges down and stops the vinyl from peeling.

   How do you apply the outside vinyl piece on a door handle?

   Heat one side of the vinyl, pull it over, and work it into the center of the handle. Cut the film on the inside to remove excess material, then repeat the process on the other side.

   What adhesive is used on Aura Vinyl vinyl wrap?

   Aura Vinyl vinyl wrap uses German-made adhesive engineered for pliability, clean repositioning, and fewer glue lines.

4. 

   Matte Color Shift Teal Purple Wrap on Audi e-tron GT

   Learn how to wrap an Audi e-tron GT rear bumper in matte color shift vinyl.

   This tutorial shows a matte color shift teal purple finish installed on an Audi e-tron GT. The video demonstrates how to wrap a rear bumper from start to finish. The installer walks through the setup, heating techniques, and edge work.

   Bumper Wrap Steps

   To wrap the bumper, follow the process shown in the demonstration:

   • Lay out your vinyl sheet across the rear bumper.
   • Tack the material down in the center to anchor it.
   • Lift the film on one side and apply heat starting from the center.
   • Glass out that portion and repeat until the entire bumper is glassed out.
   • Tuck the film as far into the edges as possible, then cut it down to shape.

   Handling Wrinkles

   If you get small vertical or horizontal wrinkles, heat them up with your heat source and work them out. Once all the air is out from behind the bumper, you can finalize your edges. Aura Vinyl vinyl wrap provides a cast polymer hybrid film with German-made adhesive for easy repositioning and fewer glue lines during installation. It also includes a PET backing for a smoother look with less orange peel.

   FAQ

   How do you remove wrinkles when wrapping a bumper?

   If you get small vertical or horizontal wrinkles, heat them up and work them out. Once the wrinkles are heated, continue working out the air before you tuck the edges.

   What is the first step in wrapping a rear bumper?

   Start by laying out the vinyl sheet over the bumper and tacking it down in the center. Then lift the material on one side and begin heating from the center to glass it out.

   What car is featured in this bumper wrap tutorial?

   The tutorial features an Audi e-tron GT wrapped in matte color shift teal purple.

5. 

   Grey Vinyl Wrap on a Tesla Model S

   Step-by-step guide to wrapping a Tesla Model S rear quarter panel in grey vinyl wrap.

   This install features a grey vinyl wrap applied to a Tesla Model S.

   The video demonstrates how to wrap a rear quarter panel step by step. It walks through setting the material, cutting around the pillar, and managing tension along the body line.

   Quarter Panel Wrapping Steps

   • Cut the quarter panel vinyl piece down to shape.
   • Peel backing paper from back to front, tack the vinyl, remove backing completely, and cut at the pillar.
   • Glass out the front section, tack along the body line, and glass the rear.
   • Lock in the body line, heat the vinyl, glass it, and squeegee down the lower section.
   • Work upward by heating and glassing the top, smoothing with a glove, and finishing the back edge.

   Tips for Clean Results

   The installer focuses on glassing each section before pressing it down. Relieving the pillar area keeps tension off the film while setting the main body line. Heating the film softens wrinkles so you can glass the surface flat before squeegeeing out trapped air. Aura Vinyl vinyl wrap features a PET-backed finish and German-made adhesive to support clean repositioning on complex panels.

   FAQ

   How do you wrap a Tesla Model S quarter panel?

   Cut the film to shape, tack it down, and separate the pillar cut so it does not stick early. Glass out the front and rear sections along the body line, then squeegee down while using heat to smooth wrinkles.

   Why do you cut the vinyl near the roof pillar during install?

   Cutting the material at the pillar prevents the upper section from sticking too early. This allows you to glass out the main body line and squeegee the lower panel first.

   What adhesive does Aura Vinyl vinyl wrap use?

   Aura Vinyl vinyl wrap uses German-made adhesive designed for pliability, repositioning, and fewer glue lines.

6. 

   Grey vinyl wrap on an Audi A7

   Learn how to wrap an Audi A7 door by working the body line and splitting sections in cold weather.

   This video shows a grey vinyl wrap being installed on a 2019-2024 Audi A7 door. The installer demonstrates an effective technique for wrapping a door panel when working in colder shop temperatures.

   Door Wrapping Steps

   The process begins by glassing out the first half of the door. The installer tacks the vinyl down along the body line to lock it into place, then glasses out the other side. Once the film is anchored, squeegee from the body line upward toward the window. Next, work below the body line by squeegeeing all the way across the panel. Always overlap squeegee strokes so trapped air flows out evenly.

   Cold Weather Technique

   Working in a cold shop can make it difficult to heat and glass out an entire sheet of vinyl at once. To make the process manageable, the installer splits the bottom section into two separate areas. He picks up the right section, applies heat, and glasses it down cleanly. To finish the door, squeegee out the remaining air, trim the vinyl to shape, and remove the excess material.

   Aura Vinyl vinyl wrap features a cast polymer hybrid build with German-made adhesive and a PET-backed finish for smooth application.

   FAQ

   How do you wrap a car door in cold shop temperatures?

   You can split the lower door area into two separate sections. Lifting and heating smaller sections makes it easier to glass out the material when cold weather makes large sheets hard to manage.

   Why is it important to overlap squeegee strokes?

   Overlapping your squeegee strokes ensures that air flows out evenly across the panel. This helps prevent trapped air pockets along body lines and flat surfaces.

   Where should you lock in the vinyl on an Audi A7 door?

   After glassing out the first half of the door, tack the film down along the body line to lock it in place. Then squeegee upward above the line and downward below it.