Reels

1. 

   Gloss Green Vinyl Wrap Gas Cap Wrap Box Install

   Watch an installer use a vacuum wrap box and heat gun to wrap a car gas cap in gloss green vinyl.

   This video shows a gloss green vinyl wrap being applied to a car fuel cap door. The clip features wrap box ASMR during the gas cap wrapping process.

   An installer uses a vacuum wrap box and a heat gun to cleanly apply gloss green vinyl wrap to the fuel cap. The film forms seamlessly over the cap with heat and vacuum before being trimmed neatly.

   Wrap Box Process

   A vacuum wrap box helps installers cover small, detached parts evenly. Suction pulls the vinyl wrap downward against the shape of the gas cap door while heat from a heat gun softens the material. This method ensures the film conforms tightly around curves without leaving loose edges. Once the vinyl cools and sits tight over the part, the installer trims away excess film.

   Vinyl Wrap Details

   Aura Vinyl provides vinyl wrap options made from cast polymer hybrid film with German-made adhesive. The PET-backed finish provides a flat surface with less orange peel. Expected lifespan for vinyl wrap is 3 to 5 years with proper care. Recommended care includes hand washing at least every two weeks with vinyl-safe products, avoiding drive-through car washes, and applying a ceramic coat before the wrap sees the sun.

   FAQ

   How is a wrap box used to wrap a gas cap?

   A wrap box uses vacuum suction combined with a heat gun to form vinyl wrap tightly over the fuel cap door. The film forms seamlessly over the surface before the excess is trimmed.

   What is the expected lifespan of Aura Vinyl vinyl wrap?

   Aura Vinyl vinyl wrap has an expected lifespan of 3 to 5 years when maintained with proper care.

   How should you care for a new vinyl wrap?

   Hand wash the wrap at least every two weeks with vinyl-safe products, avoid drive-through car washes, and apply a ceramic coat before the wrap sees the sun.

2. 

   Toyota Tacoma emblem removal before vinyl wrap

   Learn how to remove vehicle emblems and clean adhesive before installing vinyl wrap.

   This prep tutorial covers emblem removal on a metallic grey 2016 to 2023 Toyota Tacoma with factory metallic paint finish.

   The video demonstrates why you should never leave vehicle emblems on a panel while trying to wrap. Removing the badges ensures a clean finish and allows the vinyl film to lay flat across the entire panel.

   Steps for Clean Emblem Removal

   Follow these steps shown in the video to prep your vehicle badges:

   1. Use fishing line and elbow grease to cut through the emblem adhesive and pull the badge off.
   2. Attach a rubber wheel to a drill to strip off the remaining adhesive from the paint.
   3. Wipe away the loose rubber dust using a dry microfiber towel.
   4. Clean the panel before laying down the film.

   Some installers leave leftover tape behind to mark badge placement, but taking off the adhesive completely creates a much cleaner finish. Once the panel is dusted and prepped, it is ready for material. Aura Vinyl vinyl wrap offers a PET-backed finish and German-made adhesive to give installers clean repositioning and fewer glue lines during install.

   FAQ

   How do you remove vehicle emblems before wrapping?

   Use fishing line and elbow grease to slice through the adhesive behind the emblem. The badge will come right off the vehicle panel.

   How do you get leftover emblem adhesive off car paint?

   Attach a rubber wheel to a drill and run it over the leftover adhesive. Then wipe away the dust with a dry microfiber towel before spraying any alcohol cleaner.

   Should you leave emblem adhesive on to mark badge placement?

   No, leaving adhesive behind does not provide a clean finish. All residual tape should be removed with a rubber wheel so the panel surface is flat and ready to wrap.

3. 

   Toyota Tacoma hood clay bar and wrap prep

   Learn the steps to properly clay bar and prep vehicle paint before installing a vinyl wrap.

   This wrap preparation tutorial is performed on the dark gray hood of a 2016 to 2023 Toyota Tacoma. The video demonstrates why washing alone is not enough before installing a wrap, as harsh contaminants can remain stuck to the paint surface. An installer walks through how to properly decontaminate the hood using a clay bar, soapy water, and an alcohol wipe.

   Surface Decontamination Steps

   Washing the vehicle removes loose dirt, but bonded debris can still stay on the paint. To clean the surface thoroughly before wrapping, use the following procedure:

   • Spray down the entire hood with soapy water to serve as lubrication.
   • Rub the clay bar using overlapping straight strokes, moving either horizontally or vertically.
   • Never move the clay bar in circular motions.
   • Dry the entire hood thoroughly after finishing the clay bar pass.
   • Spray down alcohol over the panel and wipe it clean with a fresh microfiber towel to remove leftover soap and oils.

   Wrap Ready Surface

   After completing the alcohol wipe, the paint is contaminant-free and ready for installation. Aura Vinyl provides vinyl wrap engineered with a PET backing for a smooth finish and a cast polymer hybrid film with German-made adhesive. Taking time to clean and prep the panels helps ensure the adhesive bonds directly to clean paint.

   FAQ

   Why is washing not enough before wrapping a car?

   Even after washing, harsh contaminants can still remain stuck to the vehicle paint. Using a clay bar and soapy water removes these particles so the wrap can be applied cleanly.

   What motion should you use when clay barring a car?

   Overlap using straight strokes going either horizontally or vertically. Do not move the clay bar in circles.

   Why do you use alcohol after using a clay bar?

   Wiping the panel with alcohol and a fresh microfiber towel removes any oils or leftover soap residue missed after clay barring. This leaves the surface contaminant-free for wrap installation.

4. 

   Removing Old Vinyl Wrap From a Porsche 911

   Learn how to remove brittle vinyl wrap from a grey Porsche 911 using laminate film and heat.

   This video shows how to remove worn wrap from a grey 2019-2024 Porsche 911. An installer demonstrates a practical method to peel off brittle vinyl that has deteriorated over time.

   Wrap Removal Steps

   To lift the damaged material without it breaking into tiny pieces, the installer covers the panel with print laminate. Here is the process shown in the video:

   • Lay clear laminate film over the cooked panel.
   • Squeegee the laminate across the surface, without worrying about wrinkles.
   • Lift the edges of the wrap before working on the middle.
   • Heat the panel and begin peeling the film away.

   Lifting the edges first is essential because stuck edges make pulling the center much harder. The installer explains that while a few small fragments might stay behind on the paint, most of the old wrap pulls off cleanly with the laminate.

   Vinyl Wrap Lifespan

   Although the film being removed is not an Aura Vinyl product, Aura Vinyl sells Vinyl wrap designed with German-made adhesive and a PET-backed finish. With proper care, Vinyl wrap has an expected lifespan of 3 to 5 years.

   FAQ

   How can you remove cracked vinyl wrap easily?

   Apply a layer of print laminate over the damaged panel and squeegee it down. Warm the surface with heat and pull the laminate so the brittle wrap peels off in large sections.

   Why is it important to lift wrap edges first?

   Lifting the edges before pulling the center prevents the wrap from tearing. If the edges remain stuck down, peeling the middle of the panel becomes very difficult.

   What is the expected lifespan of vinyl wrap?

   Vinyl wrap has an expected lifespan of 3 to 5 years when maintained with proper care. Recommended care includes hand washing at least every two weeks and avoiding drive-through car washes.

5. 

   Vinyl Wrap Squeegee Technique on a Subaru BRZ

   Learn the key squeegee techniques to prevent air bubbles and wrap a Subaru BRZ cleanly.

   This tutorial demonstrates vinyl wrap application on a Subaru BRZ. In the video, an installer demonstrates proper squeegee techniques to help viewers avoid trapped air and bubbles during installation. Squeegee pressure is one of the most critical elements of a clean install. If you squeegee too hard, the tool will not move across the vinyl surface. If you do not apply enough pressure, you leave air bubbles and trapped air behind under the film. Installers need to find the balanced amount of pressure that works for them. Overlapping squeegee strokes is another key technique because it allows air to flow out evenly toward the edges of the panel. For edges that are difficult to work with, lifting the vinyl up allows you to squeegee air out toward the perimeter much more easily. Following these steps helps produce a clean and smooth final finish across the entire vehicle. Aura Vinyl vinyl wrap features a PET-backed finish and a cast polymer hybrid construction with German-made adhesive.

   FAQ

   How do you prevent bubbles when using a squeegee on vinyl wrap?

   Use balanced pressure and overlap your squeegee strokes to let air escape toward the edges. You can also lift the vinyl up to move air toward the edge more easily.

   What happens if you push too hard with a wrap squeegee?

   If you squeegee too hard, the squeegee will not move across the vinyl surface. Finding the right balanced pressure keeps the tool moving while eliminating bubbles.

6. 

   Wrap a Tesla Model 3 pillar without paint showing

   Learn how to wrap the gap between a Tesla Model 3 pillar and fender so original paint does not show.

   This installation video covers wrapping a grey 2017-2023 Tesla Model 3 along the tight seam between the pillar and fender. Cutting only on the opposite edge leaves factory paint visible if a car has bright original paint like white, red, or yellow. The video demonstrates how to use an underlay piece and knifeless tape to prevent any OEM paint from showing through the panel gap.

   Installation Steps

   1. Apply knifeless tape across the body line between the fender and the pillar.
   2. Slide a vinyl underlay piece between the fender and the pillar, then lock it onto the body line.
   3. Heat the vinyl and use a flexible squeegee to lay the material flat into the seam.
   4. Pull the knifeless tape line all the way through and remove the excess material.
   5. Lay the main pillar vinyl piece down, heat the material, let it cool, cut along the opposite edge, and tuck it deep into the gap.

   Film Details

   Aura Vinyl vinyl wrap uses a cast polymer hybrid film with German-made adhesive and a PET backing to help material lay flat and tuck cleanly into tight body lines.

   FAQ

   Why does OEM paint show between the pillar and fender when wrapping?

   Cutting vinyl film only on the opposite edge does not leave enough material to fully tuck inside tight panel gaps. On cars with contrasting original paint, that exposed gap becomes clearly visible.

   How do you hide paint gaps between the pillar and fender?

   Place knifeless tape across the body line and feed a strip of vinyl between the panels as an underlay piece. After heating and squeegeeing the strip down, cut it with the tape before applying and tucking the main pillar wrap.