Reels

1. 

   How to wrap a seamless trunk with knifeless tape

   Learn how to create clean, overlapping seams on a trunk lid using knifeless tape.

   This installation guide demonstrates how to achieve a seamless trunk wrap using knifeless tape along factory body lines. The video shows an installer wrapping a car trunk lid and creating a clean overlapping seam that follows the contours of the vehicle. To begin, lay down your first piece of knifeless tape directly across the body line. Remove the backing paper from the vinyl and tack down the material. Next, pick the material up on both sides and glass it out to eliminate tension and wrinkles. To work out all the air, start in the center and squeegee outward to the left and right. Once the air is completely removed, pull the knifeless tape all the way through to cut the vinyl, then remove the excess film. Lay down a second piece of knifeless tape over the edge to create an overlapping seam. Tack down your top piece of vinyl, pick up both sides, and glass it out once more. Establish your center line and squeegee out the air toward one side. Lock in the edge over the knifeless tape, pinch and tug the tape all the way through, and discard the excess vinyl. Aura Vinyl wrap features a PET backing for a smooth finish with reduced orange peel, paired with a cast polymer hybrid build and German adhesive for reliable repositioning.

   FAQ

   Where should knifeless tape be placed on a trunk lid?

   Knifeless tape should be laid down directly along the hard and soft body lines of the trunk lid to hide the seam.

   How do you squeegee out air during a trunk wrap?

   Start in the center of the panel and work your squeegee outward toward the left or right after glassing out the film.

   How is an overlapping seam created on a trunk?

   Make the first cut with knifeless tape, lay a second piece of tape over that edge, tack down the top vinyl panel, and pull the tape through.

2. 

   Knifeless Tape Vinyl Wrap Tip on a Scion FR-S

   Eliminate vinyl tension around knifeless tape on a silver Scion FR-S before making your cut.

   This video demonstrates silver vinyl wrap installation on a 2013-2016 Scion FR-S. The clip shows an installer eliminating vinyl tension around knifeless tape before executing a clean cut. Working with too much tension near cut lines can distort the film or pull the tape off line during an install.

   Steps to Remove Tension

   Instead of dangling the material off the car and hoping for the best, use this process to relieve stress across the film:

   1. Peel the vinyl back further than where the knifeless tape is placed on the panel.
   2. Tack the film down to the car body.
   3. Give the vinyl a little pinch so all the tension is gone.
   4. Give it a gentle tug so the material easily releases without stretching.
   5. Remove that line, lay your vinyl over the knifeless tape, and make the cut.

   Film Performance

   Releasing tension before cutting helps keep your lines straight and prevents unwanted pull. Aura Vinyl vinyl wrap uses a cast polymer hybrid film with German-made adhesive to provide pliability and repositioning on complex curves.

   FAQ

   How do you release tension over knifeless tape?

   Peel the vinyl wrap back past the tape line and tack it down. Give the film a pinch to remove tension, then tug gently so it releases before you lay it flat to cut.

   Why is vinyl tension an issue when using knifeless tape?

   Leaving tension in the vinyl can cause the film to pull or distort along the cut line instead of releasing smoothly.

   What type of adhesive does Aura Vinyl wrap use?

   Aura Vinyl wrap uses German-made adhesive designed for pliability, repositioning, and fewer glue lines.

3. 

   Roof wrap install around a shark fin antenna

   Learn how to wrap a roof without removing the shark fin antenna.

   This installation covers the roof of a gold car using Aura Vinyl PET-backed vinyl wrap. The video demonstrates how to wrap a roof when you cannot remove the shark fin antenna.

   Step-by-Step Installation

   Start by making a tape template around the shark fin antenna, then carefully remove the template from the roof. Tape up the shark fin before moving forward. Lay out the material for the roof, locate where the shark fin sits, and place down the tape template.

   Transfer the vinyl over to the glass and cut out the shape of the shark fin. Cut the opening a little bit smaller than the template rather than exact size. Remove the tape template and transfer the vinyl back to the roof with the backing paper still on to confirm alignment.

   Once aligned, remove the backing paper from one side to the other. Glass out both sides to tighten the sheet.

   Pro Tips for Tucking

   Work air out from behind the vinyl around the shark fin before moving to the sides. Lock in the area around the fin, glass out the outside, and work air out starting from the center.

   Trim the vinyl around the fin, leaving enough excess material to tuck so no gold OEM paint shows through. Lift the fin slightly and use a hard edge squeegee to tuck the vinyl beneath the base.

   Aura Vinyl vinyl wrap uses a cast polymer hybrid build with German-made adhesive and a PET-backed finish.

   FAQ

   How do you wrap a roof without removing the shark fin?

   Create a tape template around the shark fin antenna, cut the opening slightly smaller on the film, and position the vinyl over the roof. After glassing out the film, work the air out around the antenna base and tuck the excess material underneath using a hard edge squeegee.

   What size hole should be cut for the antenna opening?

   Do not cut the hole to the exact size of the antenna template. Cut the opening slightly smaller than the template to ensure there is enough material left to tuck.

   How do you tuck vinyl wrap around a shark fin antenna?

   Leave enough excess material around the fin so no original paint shows. Lift the antenna slightly and use a hard edge squeegee to tuck the wrap beneath the base.

4. 

   White vinyl wrap on an Audi A5 fender

   Learn the step-by-step beginner process for wrapping an Audi A5 front fender with vinyl wrap.

   This tutorial shows how to install white vinyl wrap on an Audi A5 front fender. The demonstration guides beginners through trimming the panel, locking in body lines, removing trapped air, and finishing edges clean.

   Panel setup and glassing

   Start by cutting the vinyl down to shape, leaving about two inches of excess material in the wheel well. Peel the backing paper back from the front of the fender and tack the vinyl into place. Pull the backing paper down, cut off the excess backing so the lower section does not stick early, and remove the protective cap sheet if the vinyl includes one.

   Next, pick the film up at the front and glass it across the main body line. Use a wrapped glove to lock the vinyl directly onto the body line. Lift the remaining material, glass it across the top rear section, lock the rest of the body line down, and work upward. To handle the lower portion of the fender, start in the center and work outward toward the sides. Pick up the material and glass it out again if needed to glove out all air pockets.

   Trimming and edge finishing

   For the wheel well, warm the material with heat and roll the film underneath the arch using your thumb. Cut the excess along the deepest edge of the wheel well. Along the door gap, trim along the opposite edge, pull away the scrap vinyl, and tuck the remainder behind the panel.

   Aura Vinyl vinyl wrap features a cast polymer hybrid construction with German-made adhesive and a PET liner, which allows for smooth repositioning and a flatter finish.

   FAQ

   How much excess vinyl should be left in the wheel well before wrapping?

   Leave approximately two inches of excess vinyl in the wheel well when cutting the material down to shape.

   How do you finish the vinyl around the wheel well edge?

   Heat the vinyl, use your thumb to roll the film under the wheel well lip, and cut along the deepest edge.

   What is the best way to lay vinyl on the lower half of a fender?

   Start smoothing in the middle and work outward toward the edges, lifting and glassing the material if air needs to escape.

5. 

   Hood vinyl wrap technique on an Audi A4

   Learn how to glass vinyl wrap and clear air pockets on an Audi A4 hood.

   This tutorial shows a vinyl wrap installation on the hood of a white Audi A4. The video demonstrates how to work vinyl across a hood without forcing squeegee strokes through wrinkles.

   Proper Glassing and Air Management

   A beginner might finish one side of a hood and immediately try to squeegee down the other side. Fighting wrinkles and air pockets directly can lead to install issues. The installer shows that picking the material up and reglassing it creates a flat surface with a much higher chance of success.

   During the installation, overlapping squeegee strokes from top to bottom is not always possible. Instead, push smaller bubbles together into larger air pockets. Once those pockets form, you can lift the film again and glass it out to remove soft wrinkles.

   Working Out Stubborn Wrinkles

   When squeegeeing down the film, work in the direction that air pockets naturally flow so the trapped air can escape. For stubborn, hard wrinkles, lift the vinyl, apply heat, and glass the sheet back down over the hood surface. Squeegee out the remaining air and repeat this process across the rest of the panel.

   Aura Vinyl vinyl wrap features a cast polymer hybrid construction with German adhesive and a PET-backed finish designed for repositioning and smooth application.

   FAQ

   How do you fix stubborn wrinkles when wrapping a hood?

   Lift the vinyl wrap off the panel, apply heat, and glass the material back out over the surface.

   Why should you glass vinyl wrap instead of squeegeeing wrinkles?

   Squeegeeing directly into wrinkles can trap air pockets and cause install failures. Lifting the vinyl and reglassing it relaxes soft wrinkles and lets trapped air escape naturally.

6. 

   Measuring vinyl wrap on an Audi S5

   Learn how to measure panels accurately before cutting vinyl wrap material.

   This tutorial demonstrates how to measure panels on a white 2013 to 2017 Audi S5 before cutting vinyl wrap material.

   Proper panel measuring

   The video shows an installer measuring car panels to prepare vinyl wrap sheets. To avoid cutting a piece out too short, you should always measure carefully across the entire surface of the body panel before making a cut.

   The main tip shared in the tutorial is to leave at least two to three inches of excess material on each side of the panel. Adding two to three inches around all edges provides the extra coverage needed to tuck the film securely behind body lines and corners. Cutting panels too close to the exact edge size can leave you without enough material during stretching and laying.

   Film features

   Aura Vinyl produces cast polymer hybrid vinyl wrap engineered with German-made adhesive. This adhesive allows easy repositioning and helps prevent glue lines during the wrap process. The film also features a PET backing that creates a smooth finish with reduced orange peel.

   FAQ

   How much extra vinyl should you leave when measuring a panel?

   You should leave at least two to three inches of excess vinyl wrap on each side of the panel. This provides enough material to cover all edges without coming up short.

   What vehicle is featured in the tutorial?

   The vehicle shown in the video is a white 2013 to 2017 Audi S5.