Reels

1. 

   Green vinyl wrap on a 1992-1999 BMW M3

   Watch an installer wrap a BMW M3 trunk lid in two pieces using knifeless tape along the body line.

   This project features a green vinyl wrap with a PET-backed finish on a 1992 to 1999 BMW M3. The video demonstrates how to wrap the trunk lid using a two-piece method along the factory body line. Splitting the trunk into two sections makes the process much easier for first-time installers. The installation begins by placing knifeless tape directly across the trunk body line. Next, lay out the first piece of vinyl across the bottom section and glass it out on both sides to remove tension. Squeegee the bottom section thoroughly to work out all trapped air. Once the bottom is set, apply a second line of knifeless tape overlapping onto the first piece of vinyl. For the upper section, lay out the top sheet of vinyl. Trim away any excess film near the rear glass so it does not touch the window. Pull the backing paper completely through, lift the material, and glass it out on both sides until all wrinkles disappear. Squeegee from the center outward to split the panel into two workable sections and push out the remaining air. Finally, squeegee firmly over the knifeless tape line, pull the knifeless filament through the film, and remove the excess material for a clean seam. This wrap uses Aura Vinyl vinyl wrap, a cast polymer hybrid film engineered with German-made adhesive for easier repositioning.

   FAQ

   Why wrap a trunk lid in two pieces instead of one?

   Wrapping a trunk in two pieces makes the job easier for beginners by reducing tension. Using the natural body line helps hide the seam.

   How do you use knifeless tape on a trunk body line?

   Lay the knifeless tape along the body line before placing the vinyl. Squeegee the film over the tape line, then pull the filament through to cut the excess cleanly.

2. 

   How to tuck vinyl wrap behind rubber window seals

   Learn how to use folded backing paper to tuck green vinyl wrap cleanly behind rubber window seals.

   This tutorial demonstrates how to tuck green vinyl wrap cleanly behind rubber seals on a car. The video shows an installer working along a window edge using a simple shop technique to prevent the film from grabbing or wrinkling.

   Tucking Steps

   To get a tight edge without tearing the film, follow these steps:

   1. Cut the vinyl on the opposite edge of the panel.
   2. Fold a piece of backing paper in half with the slick side facing outward, creating a sharp crease.
   3. Slide the folded backing paper directly between the vinyl wrap and the rubber seal.
   4. Use a thin hard squeegee to tuck the vinyl behind the backing paper.
   5. Shimmy the backing paper along the seam while continuously tucking the film behind it.

   Edge Finish

   Using the slick backing paper keeps the adhesive from sticking to the rubber before it reaches the proper depth. As you move along the channel, the material seats smoothly for a flush, professional finish. Aura Vinyl provides vinyl wrap with a cast polymer hybrid construction and PET backing designed for clean installation and repositioning.

   FAQ

   How do you tuck vinyl wrap behind rubber seals?

   Slide a piece of backing paper folded slick side out between the vinyl and the seal. Then use a thin hard squeegee to tuck the film behind the paper.

   Why do installers use backing paper when tucking vinyl?

   The slick side of the folded paper allows the film to slide into the molding channel smoothly without sticking to the rubber.

3. 

   How to Pull Knifeless Tape on an Edge

   Learn how to start and pull knifeless tape cleanly when wrapping edges that are not tacked down.

   This installation tutorial shows how to cut a clean line on a dark green vehicle wrap using knifeless tape. The video demonstrates how to start the cutting filament when the excess vinyl hangs past an edge and cannot be tacked flat to a body panel.

   Steps for Untacked Edges

   When knifeless tape dangles off a panel edge, starting the filament without tearing the material can be difficult. The video provides a simple technique to secure the start:

   1. Make a relief cut in the vinyl at the length needed for the finished edge.
   2. Hold the knifeless tape directly against the bottom edge of the vinyl.
   3. Fold the vinyl wrap over the tape to sandwich the filament.
   4. Give the folded material a light pinch to hold it in place.
   5. Tug the tape filament firmly to begin the cut.

   The installer notes that you must avoid pinching too tightly. Holding the fold lightly allows the cutting line to snap cleanly through the center of the vinyl without tearing the surrounding film or shifting the edge placement.

   Aura Vinyl vinyl wrap uses a cast polymer hybrid build with German-made adhesive and PET backing to deliver flat, smooth edges during detail work.

   FAQ

   How do you start knifeless tape when it is dangling off an edge?

   Make a cut to your target edge length, fold the vinyl over the tape, pinch it gently, and pull the filament. This setup keeps the string centered so it snaps cleanly through the vinyl.

   Why should you avoid pinching the knifeless tape too hard?

   Pinching too hard stops the cutting line from releasing correctly. A gentle pinch holds the film in position while letting the filament snap through the center.

4. 

   Vinyl wrap on a 1992-1999 BMW M3

   Learn how to wrap a 1992 to 1999 BMW M3 front fender with step-by-step backing paper and glassing techniques.

   This guide covers a vinyl wrap installation on a green 1992 to 1999 BMW M3 fender. The video walks through the complete fender wrapping process on an Adam LZ giveaway car, starting from initial panel prep to the final trim.

   Fender Wrap Steps

   Proper preparation and tension control make wrapping complex body panels straightforward:

   1. Cut the material down to shape directly on the fender before laying it out.
   2. Roll the backing paper toward the back of the car starting at the front, then tack the vinyl down.
   3. Roll the rest of the backing paper and tack down the top side.
   4. Cut away excess backing paper along the bottom to keep the lower section from sticking early.
   5. Glass out the front portion of the fender, then work the entire top side down.

   Finishing and Trimming

   Next, pull the remaining backing paper from the bottom section and glass out the vinyl. Work out all the air from behind the film. Once the vinyl is flat, cut it down to shape by using the opposite edge of the fender. Remove the excess material, tuck the edges, and cut the rest of the fender for a clean finish.

   Aura Vinyl wrap uses a cast polymer hybrid construction with German-made adhesive and a PET backing for smooth results and repositioning.

   FAQ

   How do you tack down vinyl on a BMW M3 fender?

   Roll the backing paper from the front of the fender toward the back of the car and tack it down. Then roll the rest of the backing paper to tack down the top side.

   How do you cut vinyl wrap to size on a fender?

   Cut the material down to shape on the fender before laying it out. After working out the air, cut the vinyl down to shape using the opposite edge of the fender.

   What kind of adhesive does Aura Vinyl wrap use?

   Aura Vinyl wrap uses German-made adhesive designed for pliability, repositioning, and fewer glue lines.

5. 

   Prepping chipping paint for vinyl wrap on a white car

   Learn how to sand and prep flaking paint surfaces before installing vinyl wrap.

   This guide covers how to prepare a white car with flaking and chipping paint before installing vinyl wrap.

   Wrapping directly over peeling clear coat or loose paint causes immediate issues. The texture of the chips will show through the film once it is laid down. In addition, loose paint flakes pull off and stick to the adhesive backing when lifting or reglassing the material, preventing the film from sticking properly to the panel.

   How to prep damaged paint

   To fix the surface before wrapping, follow these steps:

   1. Use an orbital sander to smooth down the chipped and flaking clear coat.
   2. Check the panel to make sure the transition is flat and smooth.
   3. Spray the area with alcohol and wipe it clean.
   4. Apply a small test piece of vinyl wrap to verify proper adhesion and surface flatness.

   Once the surface is completely level, the installed film will lay flat without visible paint edges underneath.

   Aura Vinyl vinyl wrap features a cast polymer hybrid construction with German-made adhesive and a PET backing for a smooth finish across properly prepped body panels.

   FAQ

   Can you apply vinyl wrap over chipping paint?

   You should not apply vinyl wrap directly over flaking or chipping paint because the texture shows through the film. Loose paint flakes will also stick to the adhesive, preventing the material from bonding if you need to lift and readjust it.

   How do you prep chipping paint before wrapping?

   Sand the damaged area flat using an orbital sander. Once the surface is smooth, spray it with alcohol, wipe it clean, and apply a test piece of vinyl to verify the finish.

6. 

   How to Remove Pinned Emblems on a Toyota Land Cruiser

   Learn how to safely remove pinned emblems from a vehicle panel before wrapping using heat and pry tools.

   This tutorial covers emblem removal on a white 2008-2021 Toyota Land Cruiser before wrapping.

   Removing Pinned Emblems

   Fishing line can snap when working around emblems because many vehicle badges have alignment pins behind them. To avoid breaking line or damaging the emblem, start by sliding fishing line behind the edge to lift it slightly. Next, insert a plastic pry tool behind the badge to protect the paint from scratches.

   While heating the area with a heat gun to soften the adhesive, slide a second plastic pry tool underneath. Gently work your way around the edges so the emblem does not snap into multiple pieces. The heat loosens the adhesive backing, which allows the plastic pry tools to pop the pins free from the vehicle panel without cracking the badge.

   Cleaning the Panel

   Once the emblem is off, residual adhesive remains on the bodywork. Attach a rubber wheel to a drill and carefully run it over the remaining glue to rub it off completely. After the adhesive is gone, give the panel a dry wipe to remove all dust and rubber particles. The surface is now clean, flat, and ready for vinyl wrap installation.

   FAQ

   Why does fishing line snap when removing car emblems?

   Fishing line snaps when an emblem has alignment pins on the back that stop the line from passing all the way through.

   How do you remove pinned car emblems without breaking them?

   Lift an edge with fishing line, insert plastic pry tools to protect the paint, and heat the badge with a heat gun. Work gently around the edges with two pry tools to release the pins and adhesive without cracking the piece.

   How do you clean emblem adhesive before wrapping?

   Use a rubber wheel attached to a drill to remove the leftover glue from the panel. Follow up with a dry wipe to clear off dust before applying vinyl.