Reels

1. 

   Grey wrap on a Subaru BRZ trunk

   Learn how to wrap a Subaru BRZ trunk in two pieces from the bottom up.

   This tutorial features a grey vinyl wrap installed on a 2013 to 2020 Subaru BRZ trunk lid.

   The video demonstrates how to wrap the trunk in two pieces by using knifeless tape to create a clean seam. The installer works from the lower section toward the top to produce a durable finish that hides overlapping edges.

   Two-Piece Trunk Technique

   When wrapping a trunk in two pieces, always install the material from the bottom up. This keeps the seam facing downward so it remains hidden from view. A downward-facing seam also stops dirt and water from collecting inside the edge over time.

   The shape of the panel dictates how you lay down the material. When a recess is wide and gradual, you can bridge the material into the area using your glove. Avoid bridging in small recesses where there is limited surface area for the vinyl to tack.

   Finishing with Knifeless Tape

   After setting the bottom piece, glass the top section of film over the panel. Squeegee out all remaining air from underneath the surface. Pull the knifeless tape line through the vinyl and remove the excess material to create a clean joint.

   Aura Vinyl vinyl wrap features a cast polymer hybrid construction with German-made adhesive for easy repositioning and fewer glue lines during installation.

   FAQ

   Why should you wrap a trunk from the bottom up?

   Wrapping from the bottom up keeps the seam facing downward so it remains hidden from normal viewing angles. This direction also prevents dirt and water from entering the edge of the seam.

   When can you bridge vinyl wrap into a recess?

   You can bridge the material using an install glove when the recess is wide and gradual. Do not bridge vinyl into small areas where there is not enough surface area for the adhesive to tack.

   How is the top section finished on a two-piece trunk wrap?

   Glass the top piece over the panel and squeegee out all the air. Then pull the knifeless tape and remove the excess film to complete the seam.

2. 

   Door wrap glassing technique on an Audi A4

   Learn how to glass vinyl wrap and avoid wrinkles on an Audi A4 door panel.

   This install tutorial demonstrates wrapping a door panel on a silver Audi A4 with vinyl wrap. The clip shows why you should never squeegee film immediately after laying it down, as doing so catches wrinkles. Instead, the installer demonstrates the glassing method to keep the panel flat before finishing.

   Door Wrapping Steps

   To avoid trapped wrinkles, follow the sequence shown in the video:

   1. Lift the material and glass it down, holding tension out and toward yourself on both sides.
   2. Tack down the center body line so horizontal wrinkles pop up toward the top, which makes squeegeeing above the body line much easier.
   3. Lift the material up to the body line, hold tension, and glass it down flat.
   4. Squeegee around the door handle and down the center to lock the film in evenly.
   5. Work air out toward the bottom edge.

   Fixing Wrinkles and Film Details

   If wrinkles develop while working the film down, lift the vinyl, apply heat to relax it, and glass it back into place before squeegeeing again. Aura Vinyl vinyl wrap utilizes a cast polymer hybrid film with German-made adhesive and a PET-backed finish to help with repositioning and minimize glue lines during installation.

   FAQ

   Why should you avoid squeegeeing wrap material immediately?

   Squeegeeing film immediately after laying it out catches wrinkles. Picking up the material and glassing it down with tension creates a smooth surface before you lock it in.

   How do you fix wrinkles during a door wrap install?

   Pick the material up past the wrinkled area, apply heat to relax the film, and glass it back down. Once reset, squeegee the air out toward the bottom.

   How do you secure vinyl around the door handle?

   Squeegee around the handle to lock it in along with the center of the panel. This keeps the material even before pushing the remaining air out to the edges.

3. 

   Gas cap vinyl wrap on an Audi A4

   Learn how to wrap a gas cap cleanly without wrinkles or lifted edges.

   This install guide demonstrates wrapping the gas cap on a silver 2002 to 2008 Audi A4. The video shows how to install vinyl around a fuel door cleanly without lifted edges or wrinkles.

   Gas Cap Wrapping Technique

   To begin, lay out and squeegee the material down over the panel. Heat the area around the gas cap, then take a finger to lock in the opposite edge all the way around the fuel door. Make a slow, consistent, straight cut through the vinyl and remove the excess material.

   To avoid wrinkles, avoid starting on the straight section of the door. Instead, start on the curved section. Apply heat to the material and use a flexible squeegee to set the curve firmly.

   Finishing the Edges

   Next, pop the gas cap open. Apply a little bit of heat and start rolling the vinyl over the curved corner. Ensure the backside of the fuel door is prepped so the film adheres properly. Following these steps leaves a clean edge that will not peel or look crusty.

   Aura Vinyl produces vinyl wrap with a cast polymer hybrid construction and German-made adhesive for easy repositioning.

   FAQ

   How do you avoid wrinkles when wrapping a gas cap?

   Avoid starting on the straight section and begin on the curved section instead. Apply heat and use a flexible squeegee to set the curve.

   How do you prevent wrap edges from lifting around a fuel door?

   Make sure the backside of the fuel door is prepped before wrapping. Lock in the edges with heat and roll the material over the corners after popping the cap open.

4. 

   Side Mirror Wrap on a 2016-2023 Toyota Tacoma

   Learn how to use a mirror tool to wrap a Toyota Tacoma side mirror.

   This tutorial demonstrates how to wrap a side mirror on a black 2016-2023 Toyota Tacoma. The installer walks through using a dedicated mirror tool to glass the vinyl evenly over the mirror face before trimming.

   Step-by-Step Mirror Wrap Process

   Using a mirror tool makes it ten times easier to glass out the material over the face of the mirror. Follow these steps shown in the demonstration:

   1. Heat the material directly on the mirror tool.
   2. Lay the heated vinyl from the inside over the face of the mirror, keeping everything tight and in place.
   3. Apply tension and heat the material on the front bottom portion of the mirror.
   4. Cut the mirror tool out of the shape.
   5. Apply heat and work out all the air from the face of the mirror.

   Finishing and Trimming

   Once all the air is out and the edges are laid down, post-heat the material before making any cuts. Use the thin gap between the mirror and the stock housing to cut the film down to shape. Finally, remove the excess material to complete the seamless installation. Aura Vinyl cast polymer hybrid films feature German-made adhesive and a PET backing that helps reduce orange peel across compound curves like side mirrors.

   FAQ

   Why should you use a mirror tool when wrapping side mirrors?

   Using a mirror tool makes it ten times easier to glass out the vinyl over the face of the mirror. It helps maintain even tension before the film is laid down.

   When should you post-heat vinyl on a side mirror?

   Post-heat the material after pushing out all the air and laying down the edges, but before making the final relief cuts.

   Where do you cut the excess vinyl on a Tacoma side mirror?

   Cut the material down to shape using the thin gap located between the mirror and the stock housing before removing the excess.

5. 

   How to stretch vinyl wrap without discoloration

   Learn how to stretch vinyl wrap properly so the film stays in place without discoloration.

   This demonstration covers how to stretch silver vinyl wrap without causing damage to the material. The video shows the right and wrong way to stretch vinyl when you come up short on coverage during an install. When installers stretch only a small lifted section after heating, the film develops a clear discoloration mark. That concentrated tension also causes issues later in the install. When you cut the edges and apply post-heat, a piece stretched in a tiny area shrinks back from the edge. To avoid this problem, pick up the majority of the panel or section you need to extend. Heat that larger piece evenly before pulling and tacking it down. Spreading the tension across a larger area prevents discoloration marks. When you post-heat the material after trimming along the edge, the vinyl stays firmly in place instead of pulling back. Stretching should only be done when you absolutely have to get out of a jam. Aura Vinyl offers vinyl wrap made with a cast polymer hybrid film and German-made adhesive for dependable repositioning.

   FAQ

   Why does vinyl wrap discolor when stretched?

   Discoloration marks appear when you heat and stretch a tiny, isolated section of the film instead of spreading the tension across a larger area.

   How do you stop vinyl wrap from pulling back after trimming?

   Lift a majority of the piece you need to stretch and heat it before tacking it down. When you post-heat, the material will stay in place rather than shrinking back.

   When should you stretch vinyl wrap?

   You should only stretch vinyl wrap if you absolutely have to get out of a jam when you come up short on coverage.

6. 

   Ultra Gloss Green Silver Shift on a Toyota Tacoma

   Learn the correct heating technique to relax vinyl wrap wrinkles without stretching the material.

   This Toyota Tacoma features an Ultra Gloss Green Silver Shift vinyl wrap with a high-gloss Ultra Gloss finish. The video addresses questions from the Aura Vinyl installer Discord community about handling wrinkles along lower body panels without causing the vinyl to lift later. Commenters on social media expressed concern that heating the vinyl would cause it to pull back after several hours of sun exposure. The installer explains that the material is not overstretched because it is not actually stretched at all during this step. Instead, the technique relies on applying gentle heat while holding the vinyl just tight enough for the wrinkles to pull out on their own. Because the film is relaxed into place rather than forced or stretched, it stays anchored to the vehicle surface and will not pull back. Ultra Gloss Green Silver Shift is a cast polymer hybrid wrap that includes a PET backing for a smoother look with reduced orange peel, paired with German-made adhesive for easy repositioning and fewer glue lines. This vinyl wrap line has an expected lifespan of 3 to 5 years when properly maintained.

   FAQ

   Why does vinyl wrap pull back after installation?

   Vinyl wrap pulls back when it is overstretched during installation. Heating the film and holding it just tight enough to remove wrinkles keeps it relaxed so it stays in place.

   What vehicle is wrapped in Ultra Gloss Green Silver Shift?

   The demonstration features a Toyota Tacoma wrapped in Ultra Gloss Green Silver Shift with an Ultra Gloss finish.